[ Chinese wardrobe net ] The wardrobe assembly seems to be simple, but it is not. Because the wardrobe is relatively large, it is very troublesome in the process of assembly, but as long as you master the tips, it is not a problem. The following is a small series to teach you how to assemble the wardrobe.

Assembly wardrobe renderings

First, use the pad to point the floor , first assemble from the wide side plate against the end of the wall, and lay the wide side plate on the ground (maintain 700mm away from the back wall). First, put the plate of the filled three-in-one rubber plug on the cloth, check the hole spacing and the drawing, and install the three-in-one single-link. Then the solid layer is nailed to the cork, fixed on the wide side plate, the top handle with the large handle hole facing upward, the other solid layers are facing downward, and the foot line large handle hole is facing inward (the middle solid layer is consistent with the L frame height, that is, the bottom plate to the solid layer The inner space is 960mm, and the hole is drilled on site.) Put the side panels, nail the cork, and the cork is required to connect the solid layers on both sides. Install the double connecting rod on the second cabinet. Note that the large handle on the double connecting rod can only lock half, that is, 90°. When the two solid layers are fixed to the side plates, tighten the large handles at the same time. Repeat the installation steps for the second cabinet when installing the third cabinet.

Second, the nail back plate put the installed whole cabinet side on the floor of the point cloth, and the flat side plates are in the same plane. Use a slider to measure the diagonal size of the cabinet and adjust it to the same level. Start with the first backing plate from the wide measuring board. Note that if there is a solid nail in the middle, draw the center line of the solid layer with a pencil and nail it. nail.

Third, the installation of the L frame uses a side plate of the L frame on a parallel line above the corresponding side plate, then moves up 9mm to draw the center line of the three-in-one rubber particle, and draws the top frame of the L frame on the corresponding bottom plate. A parallel line, the center line of 9mm draws the center line of three rubber particles. The hole was drilled with a 10 mm drill bit and the hole depth was 10-20 mm. Install a single pole. After the L frame is installed, nails are fixed on the back plate.

Fourth, clean the wardrobe installation debris , left and right one station, the wardrobe is slightly inclined backwards, forcefully lifted, moved back to the desired position, pay attention not to scratch the floor, the wall.

Install three sections of track:

The track is placed against the drawer, flushing the drawer floor, and the moving female rail fixing sub-rail screw is mounted on the sub-track vertical eye (this is an adjustable position). The distance between the two drawer panels to the center of the track eye is further increased by 2 mm. The data of the female rails is removed and the transverse line is drawn on the side panel of the cabinet with a 90° angle. The cross-sectional line is the center line of the female rail. . The drawer panel is inserted into the column, so the vertical cut line is drawn from the outer side of the side panel of the cabinet, the female rail is flush with the vertical tangent line, the center eye is flush with the line, and the screw is mounted on the transverse eye of the busbar (adjustable position). After the drawer is installed, the adjustable position is used for debugging, so that the drawer surface is flat and the surrounding gap is even. Finally, the fixing screws are placed on the transverse eye of the sub-track and on the vertical eye of the female rail. And so on to install the next one. In the case of full drawers, the same principle can be installed from bottom to top, and the uppermost drawer can be fixed with a 90° angle. The premise requires that the surface is leveled and the apprentice is uniform. The drawer clearance is 2mm.

Plaid rack: Install three rails as well as three rails of drawers, measure the distance between the side panels and the center of the rail plus 50mm gap, and draw data to draw cross-cut lines on the side panels of the cabinet, install the female rails, debug and fix . The upper side of the side panel of the lattice frame is fixed to maintain a 50MM gap for the purpose of taking objects.

Pants rack: similar to the grid rack installation, the difference is that the side panel of the pants rack is 20mm away from the grid surface. Keeping the inner space of 20mm is also convenient for use.

5. Installation of the push-pull mirror, the three-section rail is mounted on the push-pull mirror, and the height of the push-pull mirror is generally 1700 mm above the bottom solid layer (customer can request height). The rail transverse line is drawn on the side panel at a height of 90° according to the required height. The parallel distance between the new eyes in the three-section track on the upper line is measured, and accurate data is obtained. The lower track transverse line is drawn on the side plate with a 90° angle. Install the upper and lower mother rails of the push-pull. The mother rail is 5mm away from the backboard and is equipped with a push-pull mirror.

Sixth, the installation of Yitong, from the ground level to the 38mm draw cross-cut line, the side panel is divided into the vertical cut line, the cross-pad is the center of the first eye above the clothing pass.

Animal Swim Ring

Animal Swim Ring,Deer Animal Swimming Ring,Animal Shapes Swimming Ring,Inflatable Animal Swim Ring For Kids

J&TZ CO.,LTD , https://www.inflatable-toy.com