[ Chinese wardrobe net ] The wardrobe edge banding machine is prone to failure under continuous high temperature environment, which affects the utilization rate of equipment. If the operator of the equipment mistakenly believes that the edge banding machine and the precision panel saw are mistakenly thought to be mechanically operated, the scientific maintenance and maintenance should be used to eliminate the non-substantial electrical faults to ensure the wardrobe edge. The normal operation of the machine.

Excessive welding

Analysis: Excessive energy input into the work

Solution: 1. Reduce the pressure value. 2. Reduce the welding time. 3. Slow down the speed of the upper mold.

2. Insufficient welding

Analysis: too little energy to input work

Solution: 1. Increase the air pressure value 2. Increase the welding time 3. Use a larger power model.

3. Uneven welding

Analysis 1: Workpiece distortion

Solve 1:1. Check whether the workpiece size is different. 2. Check if the operating conditions cause the workpiece to deform.

Analysis 2: The contact faces of the welding head, the base and the workpiece are not flat.

Solution 2:1, the ability point is redesigned to make the height uniform. 2. Adjust the horizontal screws. 3. Check if the operating conditions are true. 4. View the shape and size of the workpiece.

Analysis 3: The base support is not strong

Solution 3: 1. Improve the support points where necessary. 2. The base is redesigned. 3. Change to a hard base.

Analysis 4: The workpiece error is too large

Solve 4:1. Tightening the tolerance of the workpiece. 2. Re-size the workpiece. 3. Review the operating conditions. (pressure, delay time, welding time, curing time, etc.)

In order to improve the quality of the products, the following points are raised for several problems that arise in the edge banding machine:

1. Before the guide rail is installed, check whether the guide rail is flat. Both ends of the guide rail must be flush and quenched.

2. Machining For parts that are externally processed, if they are not processed according to the drawings, they will be returned, and the foreign manufacturers will be responsible for certain losses. For parts processed in the factory, if not processed according to the drawings, the person in charge of the installation has the right to return it and re-process it. For those who cannot be reprocessed, the party shall compensate the full material and labor costs.

3. Bearings for the rubber pot part and the pulley part will all use imported skf bearings, be careful not to be confused, the bearing must be installed according to the installation process.

4. Do not hit hard when installing the conveyor motor! Otherwise the device inside the gear unit will be damaged.

5. Chains should not be too tight or too loose, whether it is a drive chain or a conveyor chain!

Edge banding machine maintenance importance

Careful care of the equipment during the use of the wardrobe edge banding machine can speed up the project schedule and reduce maintenance costs. Do not use heavy maintenance, the correct use and maintenance of construction machinery can be summarized as: reduce the load, pay attention to inspection, strengthen lubrication. As long as the maintenance and maintenance of construction machinery are emphasized and implemented as required, it will reduce the occurrence of early failures, prolong the service life, improve the operation efficiency, and make woodworking machinery bring you more benefits.

1. During use, it will not affect safety or driving due to mechanical accidents.

2. The technical status of each assembly, zero and parts of the machine is balanced to achieve the longest overhaul interval.

3. Make the machine always in good condition and start running or getting out at any time.

4. Under reasonable conditions, it will not stop due to damage in the middle.

After the pre-milling, the workpiece is not straight, or the end face is collapsed:

? The front and rear milling cutters are not adjusted in a straight line

? The line point parameter setting is incorrect. At least one knife is not cut, resulting in chipping.

• The cutter is hurt or too blunt, causing chipping

Wide Lane Turnstile Gate

General turnstile gates are common equipment suitable for pedestrians. When pedestrians carry large suitcases, push strollers or wheelchairs, conventional turnstile gates cannot meet this type of traffic demand and must be equipped with wide lane barrier gate, wide channel Turnstile Gate or wide access turnstile gate to manage.

Wide Lane Barrier Gate,Wide Channel Turnstile Gate,Wide Access Turnstile Gate,Wide Lane Turnstile Gate

Guangdong Zecheng Intelligent Technology Co., Ltd , https://www.zechengsecuritys.com