How to solve the common faults of the offset machine of the offset press
Printability differences sheetfed offset printing machines of large, Bo Hou different paper paper collection problems occur during printing device different graphic information are different, this article, the author focuses on delivery of Common Troubles and solutions for Peer reference. The print on the surface of the take-up reel is dirty 1. Anti-smash treatment method (1) Adjusting the position of the star wheel The domestic offset printing machine generally adopts a skeleton-type delivery roller, and has a simple structure. By adjusting the position of the star wheel, most of the printed products can be prevented from being dirty, and the manufacturing cost is relatively low. This method is generally suitable for black and white or relatively simple color prints to prevent smashing. (2) Anti-mite cloth / anti-smudge paper (glass ball sandpaper) A tamper-proof cloth can be installed on the surface of the flat take-up reel, such as Heidelberg's special super blue cloth. The surface structure can reduce the contact area with the paper and cushion the shock absorption to achieve the purpose of preventing smashing; On some Japanese offset presses, you can manually put anti-smudge paper (glass ball sandpaper), relying on the sharp points on the surface of the glass ball sandpaper to hold up the surface of the print, so as to prevent smudging, but after using the glass ball sandpaper for a long time, The ink gradually fills the gap between the sphere and the surface of the sphere, making it lose its anti-smashing effect. Therefore, depending on the application, it is recommended to scrub it once a day to extend the life. It should be noted that whether it is super blue cloth or anti-smudge paper, after a certain period of time, the anti-smudge effect will be reduced and it needs to be replaced regularly. (3) Anti-sludge air cushion roller The anti-smashing air cushion cylinder belongs to the patented technology of Roland offset printing machine, which is easy to operate and can last for a long time. However, due to the high manufacturing cost, only high-end models have this feature, or you need to purchase this feature when purchasing equipment. 2. Pickup roller surface cleaning method Regardless of the type of anti-smashing device, it is necessary to regularly clean and scrub the surface to ensure that the surface is clean and there are no ink bumps. It is recommended that the operator scrub the surface of the delivery roller or use a wind gun to wash the tamper every day after work. Dirty cloth. Paper reducer (brake roller) does not have enough air intake 1. The overall deceleration effect is poor (1) Fault phenomenon When the paper reaches the stack, it curls forward and collides with the front paper stopper. The curling and tearing of the crevice occurs. Adjust the suction volume of the delivery reducer and adjust the angle of the open cam to change the arrival of the paper. After morning and evening time, the effect is still not good, and it is basically determined that the reducer has insufficient air intake. (2) Solution First check whether the external suction filter of the reducer air pump accumulates a large amount of dust and debris, and then check whether the built-in filter of the reducer has a large amount of dust, the air filter device sucked by the air pump and the dust sprayed when the reducer is working. The filter device is inspected and cleaned to determine that the speed reducer is normal. Under this premise, increase the intake of the reducer and eliminate the fault. 2. The local deceleration effect is poor (1) Fault phenomenon The visual effect of poor local deceleration is that the paper is skewed in one direction. In severe cases, the skewed paper hits the safety device and causes parking. The poor local deceleration effect also reduces the speed of the printing equipment . This is usually caused by a deceleration wheel on both sides of the paper reducer. Gas or blockage is caused by no inhalation. (2) Solution In the stop mode, firstly through the jog control, the paper reducer is exposed to make a certain operation space and press the emergency stop of the delivery device control panel to avoid a safety accident; manually open the delivery air pump switch, take Take a piece of cut paper and test it on the surface of each reducer. Under normal circumstances, the paper is obviously sucked, but if there is no inhalation, it is necessary to determine whether the suction port is blocked, the suction port seal is aging, or the whole Block the pipe (disassemble the suction pipe below the reducer, test the suction pipe for suction) and clean it. Flat paper fan and flat paper duct are uneven in air volume Under normal circumstances, the fan air volume adjustment is consistent, and no independent adjustment; if the image information (ink amount) is unevenly distributed (such as one side of the solid printing, one side of the text printing), the paper is skewed, you can rebalance the fan and The amount of air blown by the air duct reduces the skewed state of the paper, so that the delivery is smooth again. It is also possible to pad the wedge on the side of the first paper, and to make it fall quickly by increasing the height, so that the paper passes smoothly. In addition, the dust on the fan surface and the blow port of the flat paper duct should be cleaned regularly to prevent clogging. Paper speed reducer (brake roller) is not suitable for rotation speed 1. The speed is too slow (1) Fault phenomenon Regardless of the thickness of the paper, when the speed reducer is inhaled normally and the speed is too slow, the moving paper will accumulate on the surface of the reducer, eventually causing the reducer to lose its function, and paper picking problems such as paper jams and roll papers may occur. (2) Solution In the actual production, through the printing paper, the paper-receiving state is observed at different speeds, and the speed of the speed reducer is manually adjusted to achieve a smooth delivery. When printing thick paper, the operator must not only adjust the current speed of the reducer, but also adjust the running time of the open cam to avoid the occurrence of dirty scratches. 2. The speed is too fast (1) Fault phenomenon When printing on one side, the speed of the reducer is too fast, and the fault phenomenon is not obvious. When the double-sided printing is performed, since the speed of the reducer is faster than the speed of the moving paper, the surface information of the paper on the printed side is excessively rubbed, thereby Scratches appear; when printing on thinner paper, excessive curling and cracking of the paper mouth may occur. (2) Solution When printing on both sides, it is necessary to continuously check the quality of the reverse image, adjust the speed of the reducer in time, observe and judge the quality of the delivery, adjust it in time, and master the operation skills and rules. Pay attention to the air blower of the air cushion fan, and use the force formed by the fan to form an air cushion between the reducer and the paper to avoid smudging. In the process of troubleshooting, the operator must be good at observing and analyzing the fault phenomenon, correctly and reasonably adjust the working state of each delivery device, regularly do the maintenance and maintenance work of each device, adhere to the "complex problem, simple start" The logic of thought uses the elimination method to find out the cause, eliminate the fault, and improve the effective production time.
Whether you need a Laptop Cart, height
adjustable desk, or a mobile lectern, the Single Column Standing Desk | Laptop
Stand offers a cost effective, no frills choice. To find the ideal standing or sitting setting.
Additional user friendly features of the laptop cart include a single column
construction and a specially designed base to optimize leg room. A sturdy all
metal frame, meanwhile, ensures durability. wide surface provides plenty of
room to work while maintaining a small footprint. All in all, it`s an
indispensable tool for any classroom room, training room, or multifunctional
office.
Conference Table,Adjustable Lectern,Adjustable Workstation,Height Adjustable Workstation Foshan Hollin Furniture Co.,Ltd , https://www.chnhollin.com