Buy a little dry sanding paper. Make a little bit of kerosene in the place where the glass is drawn. So fast. Buy a handle with a glass knife in the hardware store. The so-called blow-blowing method of blowing into a preliminary type and then blowing into a product is suitable for making small mouth vessels and bottles. Another method of cutting is to use a 4mm × 50mm ruler, and the glass knife is cut close to the ruler. The machine blown production machine blows the glass out of the manual and completely mechanically. The liquid glass is first cut into droplets (completed by the feeder and the scissors mechanism). The guide groove is led to the indenter and the indenter is vertically upward. The tips are extruded into a cake and then turned to the blower by the tip. In a short time, the abrasive tool was opened and a transparent solid glass semi-finished product came out. Hand-blown production occurs in the process of hand-made glass. Because the hot glass paste flows slowly, the air between the glass blocks naturally forms bubbles because it cannot float out of the surface. The artists often express the life quality of the glass with bubbles and become an appreciation. Part of the glass art. It's ok to get the right size. Use jade or cotton thread with kerosene. The blowing machine is a large-scale equipment like a large grinding disc. The cake is brought to the blower table by the suction head, and then the blower blows the head and blows the cake, blows the egg-shaped prototype bubble, and then the product abrasive. Clipped inside. In order to find a suitable blown glass product, we need to know a variety of glass, familiar with the characteristics of glass blowing process. After passing through the oven, the ink will dry out and the pattern will not be easily erased. It can be used with a thin wire. Auxiliary fixture: The fixture is made according to the drilling position and the diameter of the hole. The diameter of the hole in the middle of the fixture is 1 - 2 mm larger than the diameter of the drill. The thickness of the plate is 2-3 mm. Knock out the cracks that run through both sides. Use a drill press to hold the special glass drill bit. Put in water.

How to open a round hole in the window glass first. The screen printing equipment of the mobile phone casing spraying line generally uses the silk screen printing process for the monochrome gradient. The screen printing machine is a machine for printing with the screen printing plate, which belongs to the printing machine. How to make a blow molding machine The glass blower employs a hollow iron pipe with a length of about 5M. One end draws the glass liquid (pick-up material) from the furnace, and one end is a mouthpiece. The related concept wedge wedge (xiē) is a simple mechanical tool. Then slowly grind with sandpaper. The magnetron sputtering coating vacuum chamber has a number of connecting valves for connecting various auxiliary pumps. (This process is a key position. The action between the guide trough, the indenter and the tip is synchronous. The process from high temperature liquid glass to finished glass is affected by mechanical contact. The temperature becomes uneven and will be severe. It affects the effect of the lower wire blowing. The viscosity of the upper glass liquid is different from the viscosity of the glass liquid near the bottom of the crucible. Pay special attention when picking the material. The weight of the material should be basically the same every time, because the molding method mainly depends on the hand feeling and experience. Therefore, the luck is right, the blowing power is just the key to ensure the size of the product. The anodized aluminum product with a film thickness of 10um or more can be used outdoors, and can be discolored without being exposed to the sun for a long time. You can try the following methods for emergency cutting of glass. : Use quartz stone. Add silicon carbide or zirconia in a copper tube. Rotate the copper tube.

A number of staggered tool marks are randomly cut in the horizontal and vertical directions in the disc. It can also be blown freely without mold, and then knocked off from the blowpipe.

Article source address: http://

Sink Faucet

Claw feet are accessories of freestanding cast iron bath tubs. Color of claw feet can be white, black, chrome, brushed nickel and oil rubbed bronze. Material of the feet is cast iron. The claw feet are in many different shapes and sizes.